Configuring iSCSI Boot for VMware vSphere in Cisco UCS Manager 2.0.x

Requirements:

Ensure that you meet these requirements before you attempt this configuration:

• The UCS is set up


• The blades and storage both have Layer 2 connectivity


• The service profile is set up with the correct VLANs on the virtual network interface cards (vNICs)


• The Cisco virtual interface card (VIC) adapter is used. The VIC adapter can be a M81KR, a VIC1240, or a VIC1280


• The minimum UCS version is 2.0(1)a


• The iSCSI qualified name (IQN) and IP address of the storage system iSCSI target portal is available


• The boot logical unit number (LUN) ID is available

Configure

This procedure describes how to configure the service profile for iSCSI boot.

1. Select the iSCSI VLAN to be a Native VLAN on the last vNIC; use the last vNIC to avoid issues with ESXi 5.0 installations.


2. Create a virtual iSCSI vNIC in order to serve as an iSCSI configuration placeholder. This is not an actual vNIC; it is an iSCSI boot firmware table (iBFT) configuration placeholder for iSCSI boot configuration. Use this configuration:
   
   
   
   • The Overlay vNICs should be the ones with native VLAN configured in Step 1.
   
   
   • Modify the iSCSI Adapter Policy only if it is necessary.
   
   
   • The VLAN is the one defined as native in Step 1.
   
   
   • Note: Do not assign a MAC address.
   
   
   
   


3. In the Servers tab:
   
   
   
   1. Click boot_from_SCSI.
   
   
   2. Click the Boot Order tab.
   
   
   3. Expand iSCSI vNICs and double-click the appropriate iSCSI vNIC in order to add it to device list.
   
   
   4. Click Set Boot Parameters.
   
   
   
   


4. Define the iSCSI boot parameters:
   
   
   
   • Set the Initiator Name Assignment to Manual, then enter the Initiator Name in IQN or extended universal identified (EUI) format. An example is iqn.2013-01.com.myserver124.
   
   
   • Enter the IPv4 Address and the Subnet Mask for the initiator. If the storage controller is on same subnet, you do not need to define a Default Gateway or any Domain Name System (DNS) servers.
   
   
   • Use the configured IQN and IP information for LUN masking on the storage controller.
   
   
   
   


5. Click the plus (+) sign in order to add storage target information:
   
   
   
   • Enter the iSCSI target IQN name in the iSCSI Target Name field.
   
   
   • Enter the IP Address of the target iSCSI portal in the IPv4 Address field.
   
   
   • Change the target LUN ID if necessary.
   
   
   
   


6. Associate the service profile with the server.

Troubleshoot

This section provides information you can use to troubleshoot your configuration.

1. If the service profile fails to associate to the blade, and if you receive this error message, check the overlay vNIC native vLAN configuration to verify that the correct vLAN is selected.


2. If the blade fails to attach the LUN after service profile association, connect to the UCS Manager (UCSM) command-line interface (CLI). This is an example of a successful connection:
   

   
   

   F340-31-13-FI-1-A# connect adapter 1/1/1 
   adapter 1/1/1 # connect
   No entry for terminal type "vt220";
   using dumb terminal settings.
   
   adapter 1/1/1 (top):1# attach-mcp
   No entry for terminal type "vt220";
   using dumb terminal settings.
   
   adapter 1/1/1 (mcp):1# iscsi_get_config
   
   vnic iSCSI Configuration:
   ----------------------------
   
   vnic_id: 5
             link_state: Up
   
          Initiator Cfg:
        initiator_state: ISCSI_INITIATOR_READY
   initiator_error_code: ISCSI_BOOT_NIC_NO_ERROR
                   vlan: 0
            dhcp status: false
                    IQN: iqn.2013-01.com.myserver124
                IP Addr: 14.17.170.2
            Subnet Mask: 255.255.255.0
                Gateway: 14.17.170.254
   
             Target Cfg:
             Target Idx: 0
                  State: ISCSI_TARGET_READY
             Prev State: ISCSI_TARGET_DISABLED
           Target Error: ISCSI_TARGET_NO_ERROR
                    IQN: iqn.1992-08.com.netapp:sn.1111111
                IP Addr: 14.17.10.13
                   Port: 3260
               Boot Lun: 0
             Ping Stats: Success (9.990ms)

   
   

   
   


3. If the ping status fails, check your network configuration and IP settings. Ping must work before the initiator can attach to a target.


4. Check the Target State. In this example of a broken connection, the initiator is not registered on the storage controller. The same error is returned if LUN 0 cannot be found.
   

   
   

   Target Cfg:
             Target Idx: 0
                  State: INVALID
             Prev State: ISCSI_TARGET_GET_LUN_INFO
           Target Error: ISCSI_TARGET_GET_HBT_ERROR
                    IQN: iqn.1992-08.com.netapp:sn.1111111
                IP Addr: 14.17.10.13
                   Port: 3260
               Boot Lun: 0
             Ping Stats: Success (9.396ms)

   
   

   
   


5. If ping is successful, but the target state is not valid, check the LUN masking configuration and host registration on the storage controller.